The T-Clamp">12 Deep Throat Clamp is used for welding or fabricating large pieces of metal in an industrial setting. This type of clamp has a long throat to hold plates, frames, and panels away from the edge. Parts are tack-welded, assembled, or fixed with that reach and stay there. Choosing the right one isn't just about reach. You’ll also want to think about throat depth, jaw opening, frame material and finish, and adjustment style. This guide discusses 12 selection factors in layman’s terms for purchasing managers, contractors, fabricators, and distributors. Thus, they can compare options, avoid unnecessary work, and send clear instructions to a supplier such as FLA Industrial & Trading Co., Ltd.
| Type | Model | Dimensions |
|---|---|---|
| Deep Throat Clamp | Deep Throat 1.5 Inch | 35 × 110 MM |
| Deep Throat Clamp | Deep Throat 2 Inch | 46 × 140 MM |
| Deep Throat Clamp | Deep Throat 3 Inch | 82 × 110 MM |
| Deep Throat Clamp | Deep Throat 3 Inch | 85 × 185 MM |
| Deep Throat Clamp | Deep Throat Large 3 Inch | 95 × 250 MM |
| Deep Throat Clamp | Deep Throat 4 Inch | 105 × 186 MM |
| Deep Throat Clamp | Deep Throat Large 4 Inch | 110 × 305 MM |
A long frame allows a deep throat clamp to get its jaws farther away from the edge of the workpiece than a standard C clamp can. A threaded spindle can be used to convert hand torque into linear force. The part is held by the frame, the fixed jaw, the pressure pad, and the handle. From FLA’s 12 Deep Throat Clamp line, you can opt for a clamping structure with screws or one with quick adjustment. Screw-type models are best for most control, but quick-adjust models make repositioning faster when doing the same thing over and over. A deep reach does not always mean a high capacity, and I tell people buying a throat depth, jaw opening, and rated capacity that they are three different numbers.
First, find the distance between the edge of the piece you want to clamp and the point where you want to clamp it. Next, find out how thick the whole stack is, including any plates that hold it together. The breath in must clear the first number, and the breath out must clear the second. FLA lists throat depths between 1.5 and 4 inches and sizes between 35 × 110 mm and 110 × 305 mm. If your part needs more reach than these sizes offer, you can choose a design that isn't standard. Before you place an order, ask for a three-dimensional drawing. Check the spindle's travel and the diameter of the pressure pad as well. A small pad can dent a thin sheet.
Welders hold plates, brackets, tubes, and frames in position for tack welding with deep throat clamps. Metal expands and contracts when heated, and if it is held firmly in several places, it won't warp. This is something discussed in Manufacturing Engineering and Technology. AWS D1.1 has requirements for structural steel fit-up and tack welds, and a stable clamp helps with both. You have to make room for the electrode or torch. Do not weld current to the spindle threads, as this may cause damage. The same clamp is used by plumbers to fix pipes behind walls, by body shops to fix frames, and by woodworkers to fix cabinet backs and deep drawer boxes.
There isn't a clamp that works for everything. For small parts with open edges, a regular C clamp is faster and lighter. Most of the time, bar and F clamps open wider and set up faster than deep throat clamps. However, a deep throat clamp does focus pressure at a deep, fixed point. Fixed jaws make contact simple and stable, while swivel jaws can adjust to surfaces that aren't flat or straight. Screw-type and quick-adjust mechanisms also have pros and cons. One is better for keeping control, while the other is better for speed. I think you should choose by application first, then by product type. Most of the time, a deep throat design is best for parts with recessed or wide clamping points.
The quality of the frame, thread finish, pad design, and spindle all affect how long a 12 Deep Throat Clamp will last. FLA's clamps are made of carbon steel or alloy steel, and the outside can be nickel-plated or painted to keep it from rusting, even in damp shops. Most of the time, steel can handle being hit better than cast iron, which can be stiff but break easily when hit. Four words should be kept apart: the safe working load, the rated capacity, the maximum clamping force, and the force your hand can use. Don't just guess what the ratings and details are; ask the supplier for them in writing. Protect against corrosion based on what it will be exposed to, such as spatter, oil, coolant, humidity, or storage outside.
Being in the right place keeps the part steady and the operator safe. Make sure the spindle is lined up straight with the fixed jaw or pad. Don't load the far end of the throat unless the maker says it's okay to do so. For large parts, you may need more than one clamp spread out across the part. According to OSHA's rules about hand and power tools, workers should check them before they use them and should not use broken tools. This means that every shift, check the frames, threads, handles, and pads. To get more torque, don't slide the pipe over the handle, and watch out for pinch points and hot metal. If they still hold tight, quick-adjust models save time when setting up for work that needs to be done again.
If you ask for quotes in a clear way, you can compare suppliers based on facts. Type of clamp, throat depth, jaw opening, rated capacity, frame material, jaw type, finish, handle style, packaging, labeling, and spare parts should all be written down. Add the quantity, the annual demand, the number of samples needed, the lead time, the warranty, and the shipping documents for large orders. A good manufacturer should give you inspection standards, drawings, information about each batch, and compliance papers. Certification makes people more likely to trust a company. FLA has both ISO 9001 and CE certifications. ISO 9001:2015 sets requirements for a quality management system. For custom projects, you may also need prototypes, tests, and approval before production.
The choice objective stays the same with a weighted matrix. Score each candidate on dimensional fit, capacity, materials, jaw protection, operating speed, supplier documentation, and total cost of ownership. Then, sort the scores by how important they are to you. In a welding shop, the finish and ease of cleaning may be important. In a humid or outdoor location, corrosion protection may be important. And on a high-volume line, ergonomics and spare parts supply may be important. This way, I don't have to worry about two common mistakes: buying a clamp that is too big for the job or too small for the shop floor. It also gives your team a clear record of why the choice was made.
Before placing a large order, use samples to test on your actual materials, thicknesses, and fixture layouts. Check for smoothness, pressure-holding ability, surface marking, reach, jaw opening, spindle alignment, and spatter exposure. Have the acceptance requirements in writing and ask for records or inspections when your application needs them. You need to watch setup time, clamps per assembly, distortion, rework, pad replacement, and returns once the system is live. Those numbers tell us if the model has real value to measure or not. FLA helps out with design advice, 3D visualizations, and production updates. This allows buyers to check a design before it goes into mass production.
Every shift, brush the frame, spindle, jaws, and threads of the 12 Deep Throat Clamp clean of oil, chips, dust, and spatter. Use a lubricant that works well in your temperature and work environment and follow the supplier’s instructions. Look for cracks, bent frames, broken threads, loose pads, rust, and handles that aren’t straight anymore. Remove any clamp that is not safe from service immediately. Clamps with replaceable screws and pressure pads can cut lifecycle cost, but only if you can find the right parts easily. Check that you have the correct model, size, and thread specification before reordering wear parts.
Most people make the mistake of choosing based only on throat depth. Reach doesn't tell you anything about capacity, rigidity, or durability, so you should look at the rated pressure, opening range, frame cross-section, and spindle design all at the same time. Too much weight on a clamp can damage the frame, strip the threads, cause the jaws to slip, leave marks on the part, or hurt the person using it. The condition of the surface is also important. Parts that are curved, coated, polished, or fragile may need swivel jaws or protective pads. In the end, don't skip checks with suppliers. Before you make a decision, you should ask for drawings, clear ratings, sample approval, quality records, and information on delivery.
Break down your requirement into a list of items to be measured, e.g. throat depth, jaw opening, capacity, material, spindle type, jaw style, finish, spare parts, and spare parts. Standard items are good for projects where the sizes, availability, and performance are already fine. If you have special requirements for reach, jaw configurations, fixture integration, packaging, or documentation, custom solutions are the way to go. Review the drawings, samples, order quantities, inspection criteria, and delivery dates before giving your approval. A short final checklist of technical fit, testing, compliance, and total cost of ownership keeps the purchase on track.
You can get deep throat clamps from FLA Industrial & Trading Co., Ltd. in carbon steel, alloy steel, or painted steel with nickel plating. They can be used for working with metal, wood, and pipes. The current models are shown in the table.
ModelDimensionsDeep Throat 1.5 Inch35 × 110 mmDeep Throat 2 Inch46 × 140 mmDeep Throat 3 Inch82 × 110 mmDeep Throat 3 Inch85 × 185 mmDeep Throat Large 3 Inch95 × 250 mmDeep Throat 4 Inch105 × 186 mmDeep Throat Large 4 Inch110 × 305 mm
As we improve our designs, the look and specs of the product may change, so please check the details against the real product.
Our clamps are forged, stamped, machined, assembled, and finished. Each batch of steel is tested for its composition prior to starting production. We also check the thickness of the plating and the bond of the paint for ongoing corrosion resistance. Before packing, each clamp is tested for its clamping force, screw smoothness, and structural integrity. We have got the certificate of ISO 9001 for our quality management system. We have got the CE certificate for all our Products" target="_blank" style="color:blue" >products. We have been manufacturing our hardware tools, Woodworking Clamps, electrical line tools, and malleable iron pipe fittings for almost 40 years. We sell to U.S. customers, Germany and Australia, and work with Fortune Global 500 companies with them.
Most of the time, both standard and custom sizes are required by contractors and distributors. We have 2,000 tons of standard items in stock and can ship quickly. Custom orders are completed in 7 to 15 days. We can also make parts with non-standard sizes and shapes according to your drawings. If you ask for pricing information, technical details, or 3D plans, we will respond with full details within 24 to 48 hours. There is no minimum order size, so you can order as few as one clamp or as many as you need. Buyers may get all their hardware from one supplier, with more than 1,000 product specs available.
If you are picking a 12 Deep Throat Clamp for large welding and fabrication jobs, you need to make sure it fits the part and not just a single number. Throat depth, jaw opening, and rated capacity are three different specs, all of which must fit the workpiece and fixture. The screw-type and quick-adjust designs, fixed and swivel jaws, and steel frames (nickel-plated or painted) are for different purposes such as control, speed, or corrosion resistance. Use only when the tools are in proper alignment, and always check before use; do not extend the handles. Clear specifications, a decision matrix, sample testing, and regular maintenance reduce the likelihood of mistakes, rework, and failures. Supplier documentation, quality certification, and spare part support are just as important as the clamp. They measure how consistently well the model you selected performs in production.
It holds workpieces in places that are far from the edge, like inside wide, recessed, or wavy assemblies. Some common uses are tack welding, glue-ups in woodworking, installing pipes in tight spaces, and fixing car frames.
Not all the time. A regular C clamp is faster and lighter for small parts with open edges, but this one gives you more access. Pick based on where the catch point is.
Not at all. Extensions can bend the frame or strip the threads, and they make the clamp stronger than it needs to be for closing by hand. Instead, use more clamps or a bigger model.
Yes. We make parts with non-standard sizes and shapes, and custom orders are finished in 7–15 days. Sales@flaindustrial.com is where you should send your drawing or sample.
Looking for a 12 Deep Throat Clamp supplier you can trust? FLA Industrial & Trading Co., Ltd. sells clamps made of carbon steel or alloy steel that are ISO 9001 and CE certified. They come in standard sizes and can be made to order in 7–15 days. Send us your throat depth, jaw opening, material, quantity, and finish to sales@flaindustrial.com. We'll get back to you in 24 to 48 hours. For more information, go to flaindustry.com.
1. Occupational Safety and Health Administration, Hand and Power Tools (OSHA 3080), 2002
2. American Welding Society, AWS D1.1/D1.1M Structural Welding Code—Steel, 2020
3. International Organization for Standardization, ISO 9001 Quality Management Systems—Requirements, 2015
4. Industrial Press, Machinery's Handbook, 2020
5. Serope Kalpakjian and Steven Schmid, Manufacturing Engineering and Technology, 2014
6. American Welding Society, Welding Handbook, Volume 1: Welding Science and Technology, 2001
YOU MAY LIKE