A Bolted Dead End Clamp anchors an overhead conductor at a line terminal, angle point or crossing span. Next, it transmits the tension from the conductor to a pole, tower or bracket. • Locate a well. Make sure the clamp fits the actual diameter and build of the conductor. Then check that the rated load is sufficient for line tension, make sure the material and finish are suitable for your climate, and ask for test records based on IEC or ANSI standards. This guide includes information on building, installing, selecting, checking suppliers and other things which FLA Industrial & Trading Co., Ltd. needs to be able to give accurate quotes.
| Product Name | Applicable Range | Material Options | Finish | Manufacturing Process |
|---|---|---|---|---|
| NLL-1 Strain Clamp | 35-50 mm² | Aluminum Alloy with Steel Core / Ductile Iron | Hot-Dip Galvanized / Natural Aluminum | Casting, Forging, Machining |
| NLL-2 Strain Clamp | 70-95 mm² | Aluminum Alloy with Steel Core / Ductile Iron | Hot-Dip Galvanized / Natural Aluminum | Casting, Forging, Machining |
| NLL-3 Strain Clamp | 120-150 mm² | Aluminum Alloy with Steel Core / Ductile Iron | Hot-Dip Galvanized / Natural Aluminum | Casting, Forging, Machining |
| NLL-4 Strain Clamp | 185-240 mm² | Aluminum Alloy with Steel Core / Ductile Iron | Hot-Dip Galvanized / Natural Aluminum | Casting, Forging, Machining |
A Bolted Dead End Clamp, sometimes called a bolted strain clamp, is a piece of machinery that holds an overhead wire under tension. It moves the weight to a support structure. The main parts are the clamp body with the conductor groove, the goalkeeper piece, the bolts, nuts, and washers, and you can also choose to add extra reinforcement parts. In our version, we use ductile iron or an aluminum alloy with a steel core. We cast, forge, and machine it to make it. It can be hot-dip galvanized or left in its natural aluminum state. Picking the right material is important because different metals can rust when they touch in wet outdoor air. A suspension clamp is also not the same as a dead-end clamp. A dead-end clamp holds the full pulling force at the end of a span, while a suspension clamp only holds the weight of the conductor along the line.
The bolts tighten, pushing the goalkeeper against the conductor. The pressure causes friction over the area of contact. The groove shape spreads the grip along the conductor, rather than pinching it in one spot. This is to avoid damage and deformation of the strands. The holding strength is dependent on the type of clamp, the tightening torque, the diameter and construction of the conductor and the grade of the bolt. In the field, wind, ice, vibration, temperature changes and pollution also wear on the connection over time. If current is flowing through the clamp, good contact keeps the resistance low and stops the circuit getting too hot. If there is not enough torque the conductor can slip. If the torque is too high the conductor will bend and lose its grip. That's why I tell people who want to buy a clamp not to judge it by its looks or price but by how well it works in real life.
These clamps can be found at dead-end poles, angle towers, sectionalizing points, conductor transitions, and the entrances to substations. They work on distribution and transmission lines for utilities, industrial networks, railroad electrification, collection lines for renewable energy, and work to fix or replace old lines. We made this clamp for crossing spans, angle points, and terminals in power transmission and distribution systems as well as industrial power networks. Before they can order, some sites need more engineering review. Some examples are salt spray from the coast, heavy ice, high winds, pollution from factories, strong vibrations, large conductors, strange structures, limited working space, and projects that must meet utility-specific or international standards. Bringing these conditions up early helps the supplier suggest a good material and finish.
First, compare the model, conductor code, diameter range, drawings, accessories and condition of each part with the ordered one. Then prepare the conductor. Brush oxide from aluminum surfaces with a wire brush, apply an oxide-inhibiting compound where directed, and check for broken strands and sharp bends. Fit the goalkeeper in position and seat the conductor completely in the groove and torque the bolts to the correct setting. Next, check the work for alignment, nut tightness, deformation and clearances and record your findings. Schedule follow-up inspections in hostile environments. Torque values will vary according to the size of the bolt, so it's best to follow the recommendations of the manufacturer.
Datasheets for a Bolted Dead End Clamp show three types of loads: rated tensile load, minimum breaking load and recommended working load. Compare with rated tensile strength of conductor and design tension of line. Leave room for mistakes. IEC 61284 contains requirements and tests for fittings used in overhead lines and ANSI C119.4 covers connectors for bare overhead wires. Find out to what standard the clamp is made. Request test reports, certificates, data sheets and inspection records including type of conductor, arrangement of samples, test methods and failure criteria. The test should also check its resistance to pull-out, deformation under long-term load, bolt strength, cyclic loading from vibration, corrosion resistance and electrical contact where electricity flows through the clamp. Without such items, you cannot learn much from a test report.
This is what I see most often going wrong in RFQs and on job sites:.
Buying by price before fit is known. Low unit cost means little if the clamp does not fit actual outside diameter and construction of the conductor. Real size variations may be hidden behind nominal names of conductors. Provide measured diameter data and verify the allowable clamping range prior to approving any order.
Not considering torque and tightening sequence. If you guess at the torque or over-tighten bolts, you could get slippage, strand damage, or a cracked casting. Use a calibrated torque wrench and follow the printed sequence. Write down the values so that crews and inspectors are using the same numbers.
Omitting paperwork and corrosion. Later rejections cite dissimilar metals, coastal air and missing documents. Check galvanic compatibility, finish, utility approvals, drawings and test documents before shipment, as fixing these problems after delivery costs far more time than checking at the beginning.
Slippage, rework, and long-term maintenance are less likely to happen when the selection process is written down and based on things like conductor size, load needs, environment, and quality records.
Start by checking the type of conductor (AAC, AAAC, ACSR, covered or bundled) and its outside diameter, number of strands and tensile strength. This is the size of the pipe that the clamp has to be able to hold. Then check the mounting configuration, mechanical and electrical requirements and exposure at the site including temperature, pollution, wind, ice, vibration and wind. Check it against IEC, EN, ASTM, utility or project standards. When you talk to the supplier make sure you know about quality control, production capacity, export documents, samples, first article approval, on time delivery and after sale engineering support. By selecting a Bolted Dead End Clamp in this way, the product is tied to measurable facts. This allows for faster sign off of the product by an engineer or end customer.
Automatic dead-end clamps and wedge-type clamps hold the conductor by self-tightening, which can speed up installation in some situations. Crews can adjust a Bolted Dead End Clamp, re-tension a line, and look at the connection visually because it relies on controlled torque. That helps when the configuration of the conductors needs to be exact or when sag needs to be fixed after creep or storm damage. For bolted designs, you need a torque tool and it takes a little longer to finish each one. Compression dead ends, on the other hand, change shape permanently and need hydraulic tools to work. When you compare, you should look at how to install it, how well it holds, how easy it is to work on in the field, the tools needed, how often it needs to be inspected, and how much it costs. Then look at the total cost of ownership, the service life, and the project approval needs instead of just the unit price.
Let's do it in 5 steps. First, you have to describe the conductor, the line structure, the tension, the installation site, the environment, the rules and regulations. 2. Make a short list of Products" target="_blank" style="color:blue" >products which have been verified for conductor compatibility, rated load, material, mounting design and standards. Third, review the costs for testing, lead time, tools, packaging, warranty and support for each supplier. Fourth, get samples and paperwork signed off by the right engineer or end customer before ordering in bulk. Fifth, create a buying guide that you can use over and over again. This guide should contain the approved model, the torque value, the steps for inspection, packaging and replacement needs. Step five is most useful for distributors as it ensures that repeat orders are consistent from batch to batch and customer to customer.
A full RFQ makes it faster to get a correct quote. Send the type of conductor, its code, its diameter, the amount and schedule, the holding load needed, and the location where it will be installed. Include information about the material and coating, any standards that apply, the need for inspections, the destination, the packaging and labeling, and the Incoterms. It's important to look at a supplier's manufacturing capacity, engineering support, export experience, traceability, testing, OEM capability, samples, lead time, communication, and service after the sale when deciding which one to work with. Instead of just looking at the factory price, you should also look at the material grade, design complexity, hardware, coating, certification, packaging, tooling, order volume, shipping, and total delivered cost.
Before recommending a clamp, a manufacturer with real engineering depth looks at your conductor data, line loads, drawings, and mounting arrangement. It doesn't just send something from a catalog and hope it fits. You can expect to see clear drawings, size charts, installation instructions, test documents, and consistent quality records. Private labeling, custom designs, export packaging, batch traceability, and coordinated logistics can all be added value for distributors, EPC contractors, utilities, and OEM buyers. It's been almost 40 years since FLA Industrial & Trading Co., Ltd. has been making hardware tools, electrical line tools, Woodworking Clamps, and pipe fittings out of malleable iron. We work with Fortune Global 500 partners in market places like the U.S., Germany, and Australia, and we have more than 1,000 product specifications.
This is what our Bolted Dead End Clamp can do for line ends, angle points, and crossing spans:.
Materials and finish: Aluminum alloy with steel core or ductile iron, hot-dip galvanized or natural aluminum finish. Each part is cast, forged and machined so we can match material and finish to your project environment and the conductor you intend to terminate.
Quality control: Each clamp is subjected to material verification, dimensional checks, and load testing prior to shipment. Our quality management system is ISO9001 certified and our products are IEC compliant giving your engineers documented evidence for approval.
Supply and support: We carry 2,000 tons of standard products, can fill custom orders within 7 to 15 days, and offer 3D modeling and engineering support. We respond to questions within 24 to 48 hours so that project schedules are maintained.
These points answer the three most common worries buyers have: how well it fits, proof of quality, and when it will be delivered.
The Bolted Dead End Clamp is used to support an overhead conductor at junctions, angle points and crossing spans. This is achieved by converting bolt torque into a controlled grip and transmitting line tension to the support structure. Performance depends on the size and construction of the conductor, the material and finish, the tightening torque and environmental factors such as wind, ice, vibration and pollution. Comparison of the rated load with the line tension is necessary. The numbers are real, with test records linked to an IEC or ANSI standard. Bolted styles allow you to make changes and look inside. Wedge and automatic styles may be easier to install. People make most mistakes by selecting on price, guessing torque or ignoring documentation. slippage, rework and maintenance, in a five-step process. The steps are: define requirements, shortlist, compare suppliers, approve samples and establish a purchasing specification.
Ask for test reports, certificates, installation instructions, quality records, datasheets, drawings, and information about the materials. With these details, your engineer can check the product and give the go-ahead before you place a bulk order.
Only if the clamping range given covers the diameter and construction of each conductor. If you send us your conductor codes and diameters, our team will make sure they fit instead of guessing.
Yes. We work with non-standard and oddly shaped parts, and it takes us 7 to 15 days to finish custom orders. Check the specific needs of the project and approve samples before they are made.
The hot-dip galvanized finish keeps the outside safe from bad weather. Coastal salt spray needs more engineering review, so let us know how your site is set up, and we'll suggest a material and finish that will work.
Are you ready to work with a company that has been making Bolted Dead End Clamps for almost 40 years? Send your rated load, quantity, environment, standards, destination, and any private-label needs to sales@flaindustrial.com. Also include the type of conductor and its diameter. FLA Industrial & Trading Co., Ltd. has production that is ISO9001 certified, 2,000 tons of stock, custom orders that take 7 to 15 days, and replies that come back within 24 to 48 hours. For information on the product, go to flaindustry.com.
1. IEC 61284: Overhead Lines – Requirements and Tests for Fittings, 1997
2. ANSI C119.4: Electric Connectors for Use Between Aluminum-to-Aluminum or Aluminum-to-Copper Bare Overhead Conductors, 2016
3. ASTM A153/A153M: Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware, 2016
4. ISO 9001: Quality Management Systems – Requirements, 2015
5. Overhead Power Lines: Planning, Design, Construction (Springer), 2003
6. Electric Power Distribution Handbook (CRC Press), 2014
YOU MAY LIKE