A Flange By Groove Adapter connects grooved pipe to flanged valves, pumps, tanks, and other equipment, and it can also step down from a larger pipe diameter to a smaller one. It joins two connection methods in one fitting, so crews can avoid welding or threading in fire protection, HVAC, water treatment, and industrial piping. One end carries a groove for a mechanical coupling, and the other carries a flange face for gasketed bolting. Matching the flange standard, pipe outside diameter, gasket, and pressure rating determines how well the joint performs in service.
I wrote this guide for distributors, purchasing managers, site supervisors, project engineers, and MRO teams who need to pair flanged equipment with grooved pipe. Below, I cover construction, applications, selection, installation, maintenance, and sourcing, and then I answer common questions. Where a point depends on the exact product, I say so, because compatibility rests on drawings and ratings rather than on a product name.
| Type | Model (DN) | Pipe Outer Diameter |
|---|---|---|
| Flange By Groove Adapter | DN65 | 76mm |
| Flange By Groove Adapter | DN80 | 89mm |
| Flange By Groove Adapter | DN100 | 114mm |
| Flange By Groove Adapter | DN125 | 140mm |
| Flange By Groove Adapter | DN150 | 165mm |
| Flange By Groove Adapter | DN200 | 219mm |
A Flange By Groove Adapter has a flange face on one end and a grooved hole on the other end. You can connect the flange side to a valve, pump, or piece of equipment with a pin, ensuring a seal is placed between the plates. On the side with the grooves, you can put a mechanical coupling. This makes the coupling lock into place and press its own gasket against the pipe. Because the grooved side can handle small misalignments during fit-up, installers don't use heavy weld-neck flanges. This depends on the type of coupling. The coupler, nuts, and seals are not included with the adapter and should always be written down on the quote so that nothing gets missed on the job site.
There is a part of our adapters that goes from a bigger pipe size to a smaller pipe size. You can line up both centerlines with a concentric transition. This works with vertical stairs and a lot of different mechanical room setups. When you use an eccentric shift, the centerline is moved away from the run. This lets the run stay flat at the top or bottom. Based on the fluid and the direction of the pipe, that choice might help lower the amount of air or sediment that settles. Because you can't change the designs once the part is made, it's important that the drawings show the right shape.
This is our normal range. It has six sizes: DN65 (76 mm), DN80 (89 mm), DN100 (114 mm), DN125 (140 mm), DN150 (165 mm), and DN200 (219 mm). People cast, machine, assemble, and coat ductile iron or carbon steel to make the body. The look and measurements may be a little different because we are always making our Products" target="_blank" style="color:blue" >products better. Please compare them to the approved drawing or the real part. Our customization service lets you put together items of different sizes and types in unique ways.
Fire pump systems usually have spray mains with grooves and pump nozzles and valves with flanges. With a Flange By Groove Adapter, you don't have to do any hot work to connect the two. This is helpful in buildings that are already occupied, where welding would take longer than planned. NFPA 13 tells people how to build a sprinkler system in the US, and most local governments expect listed or approved parts. Our adapters have UL and FM marks on them. Still, I tell people to check the certificate to make sure it covers the right model and size before they order.
A lot of air handlers, chillers, and boilers have flanged connections. However, grooved pipes are used in a lot of hydronic loops. They can work together with a Flange By Groove Adapter in small mechanical rooms where there isn't much room for a torch. For a retrofit, crews can connect a new butterfly or check valve with a flange to a grooved loop that is already there. However, they can also make the pipe smaller where it fits. Later, when they need to fix something, they can just unbolt the joint instead of cutting the pipe. This avoids having to shut down for as long. To make sure the seal grade is correct, the system temperature and fluid level should always be checked.
To treat water, flanged valves, filters, tanks, and grooved lines are all linked together. The sizes of the parts are always changing. The red epoxy or zinc finish works well in damp rooms, but the covering should be right for the surface. For the same reason, factories use flanges and grooved headers to connect machinery and process equipment. When something is used underground, it needs to be checked for corrosion, restraint, and earth conditions more often. For dangerous services, technical approval is needed. With this range, one set of adapters can be used by contractors in water, fire, and HVAC.
The choice is not based on nominal size. Make sure you look at the pipe's outside width, wall thickness, groove size, and flange cutting. ASME B16.5 talks about Class 150 flanges, and PN16 is part of the metric DIN and EN family. For this reason, you can't just choose one over the other because the bolt circle sizes and hole numbers aren't always the same. AWWA C606 tells us what size grooved joints should be for many waterworks projects. Build the whole joint around the weakest part, whether it's the Flange By Groove Adapter, coupler, flange, bolt, or gasket.
Ductile iron is often used for water, fire, and HVAC lines because it is harder and more flexible than gray iron. Carbon steel gives you another option when the project calls for it. FLA offers a red epoxy coating or a galvanized layer to protect against rust. You should give your choice more thought if you are in a place that is humid, salty, or chemical. It is just as important for the body as it is for the cover to fit the fluid and temperature. Most grooved gaskets are made to handle water, fire, and air up to 110°C (230°F). Steam needs different things most of the time.
A flange coupling takes two ends with flanges and connects them. A Flange By Groove Adapter changes a connection with a flange to one with a groove. Geared joints are faster to use than threaded fittings, and they protect the threads from damage, which is especially important for larger lines. They don't need any hot work like welded flanges do, and the grooved side can be adjusted during assembly to line up the bolt holes. Rigid ones hold things in place, while things don't move or jiggle when they are connected to flexible ones. Because makers use words differently, technical drawings should be more important than word lists.
First, let the line drain and stop pressing down on it. Next, check the Flange By Groove Adapter, groove, pipe end, flange face, gasket, and nuts for damage or dirt. Line up the flange so that it doesn't push on the pipe, and slowly tighten the bolts in a zigzag pattern. Avoid over-tightening, as the iron flange ear might break. Next, connect the coupler on the end with the grooves and make sure the housing is all the way in. To finish, add supports, restraints, and a pressure test. NFPA 13 says that all new fire sprinkler systems should be checked at 200 psi for two hours.
You should walk along the connection after it's up and running and look for things like gasket movement, uneven flange gaps, loose bolts, coupling housings that are only partly engaged, coating that is chipped, and pipe movement that doesn't make sense. It is important to check metal often when it is exposed to water, chemicals, or salt air. Rust can start if the epoxy or galvanized layer is broken. Fix the damage to the cover as soon as possible. When you're ready to shut down, make sure you have extra gaskets on hand. They may need to be changed before the adapter does because they wear out faster.
Leaks can be caused by a gasket that doesn't work with the fluid or temperature, sealing surfaces that are dirty, flanges that aren't lined up right, bolts that aren't tightened evenly, vibration, a pipe that isn't supported, rust, or an old gasket. Read that list over before you change anything. Isolate and release the pressure in the system before you touch any nuts. Then, put in a new gasket that works with the fluid, the temperature, the pressure, and the requirements for approval. If the leak comes back, check the pipe supports. Weight that isn't being held up can put stress on the joint and make the seal less tight.
The project specs could use ASME B16.5 or ASME B16.1, DIN or EN systems for flange sizes, AWWA C606 for grooves, NFPA 13 for sprinklers, or city or county rule sets. You should ask the seller for a datasheet, a measurement drawing, a material certificate, assembly instructions, a list of the gasket's specs, instructions on how to apply the covering, certification proof, and the name of the country where the gasket was made. Before you place your order, make sure you look at these. Items that look the same might not have the same size range, certification coverage, or flange drilling.
For almost 40 years, FLA Industrial & Trading Co., Ltd. has been making more than 1,000 different kinds of hardware tools, Woodworking Clamps, electrical line tools, and malleable iron pipe fittings. We check the raw materials' chemistry and mechanical properties for these Flange By Groove Adapters. We also cast and mill them to make sure the sizes are within acceptable ranges. We also check the coating's adhesion and thickness, put them under hydrostatic pressure, and look at them one last time and measure them before packing. Our quality method is based on ISO9001, and our adapters are approved by UL, FM, and CE.
A complete request includes size, outside diameter of the pipe, flange standard, pressure class, material, coating, seal type (centric or eccentric), number, packing, shipping date, and approvals. There is more than one way to compare costs, not just the unit cost; this needs to include the cost of shipping, taxes, paperwork, and the chance of being late. Don't forget to add the connections and seals. We keep 2,000 tons of standard items in stock, and it takes 7–15 days to deliver items in any shape or size that you need. We email quotes, confirmations of unit weight, or 3D drawings within 24 to 48 hours. We keep you up to date in real time on the progress of your order, which can be anywhere from ten to ten thousand pieces. Fortune Global 500 partners believe in us, and people from the US, Germany, and Australia buy from us.
A Flange By Groove Adapter changes the size of a fitting while connecting grooved pipe to flanged equipment. It is used in fire protection, HVAC, water treatment, and industrial systems. It saves time and work by eliminating the need to weld and thread. Which unit is best depends on the thickness of the pipe's outside wall, the flange's standard, the pressure level, the body material, the coating, the seal, and whether the form is concentric or eccentric. The limit for the whole joint is set by the weakest part of it. For a good fit, it's important to isolate, clean, tighten the bolts in a crisscross pattern, make sure the couplings are fully engaged, and test the pressure. Problems with the gaskets and coatings are caught early by regular inspections. When papers are checked and total costs are compared, order mistakes and project delays are less likely to happen.
Yes. Between the Flange By Groove Adapter face and the mating flange, put a regular rubber or composite flange gasket. The adapter does not include it.
Yes, if that SKU is drilled to ISO or DIN metric standards. You'll need to say whether the drilling pattern is ANSI or PN when you place your order, because they rarely interchange.
Not often. A lot of grooved gaskets and ductile iron adapters can handle water, fire, and air up to 110°C (230°F). For steam, it's important to use various elastomers and different ratings.
The torque isn't just set by the adapter; the bolt size and grade are also important. Tighten in a crisscross pattern, because if you tighten the iron ear too much, it could break.
Searching for a company you can trust to sell Flange By Groove Adapters? The adapters that FLA Industrial & Trading Co., Ltd. makes are made of ductile iron and carbon steel and are finished with epoxy or galvanizing. They are certified by ISO9001, UL, FM, and CE, and they always have 2,000 tons of standard stock on hand. To order, email sales@flaindustrial.com with your purpose, size, flange standard, and number. Our team will get back to you with a price in 24 to 48 hours. More details are available at flaindustry.com.
1. AWWA C606: Grooved and Shouldered Joints, American Water Works Association, 2015
2. ASME B16.5: Pipe Flanges and Flanged Fittings, American Society of Mechanical Engineers, 2020
3. ASME B16.1: Gray Iron Pipe Flanges and Flanged Fittings, Classes 25, 125, and 250, American Society of Mechanical Engineers, 2020
4. NFPA 13: Standard for the Installation of Sprinkler Systems, National Fire Protection Association, 2022
5. ASTM A536: Standard Specification for Ductile Iron Castings, ASTM International, 2019
6. ISO 9001: Quality Management Systems – Requirements, International Organization for Standardization, 2015
YOU MAY LIKE