A Wedge-Type Clamp secures overhead conductors by using line tension to pull a wedge into a tapered body, which tightens the grip as the load rises. It suits selected dead-end, terminal, anchoring, and service-drop applications when the conductor diameter, working load, and environment match the manufacturer's approved ratings. Correct selection, careful installation, and routine inspection keep the termination stable and protect the conductor from slippage and strand damage. In this guide, I explain how the clamp works, where it fits, how to choose it, and what procurement teams should confirm before ordering.
| Product Name | Applicable Range | Material Options | Finish |
|---|---|---|---|
| National Standard Hot-dip Galvanized NX-1 (Upper Handle) | 6.6-7.8mm | Steel/Aluminum Alloy | Hot-Dip Galvanized/Natural Aluminum |
| National Standard Hot-dip Galvanized NX-2 (Upper Handle) | 9-11mm | Steel/Aluminum Alloy | Hot-Dip Galvanized/Natural Aluminum |
| National Standard Hot-dip Galvanized NX-3 (Upper Handle) | 13-14mm | Steel/Aluminum Alloy | Hot-Dip Galvanized/Natural Aluminum |
| National Standard Hot-dip Galvanized NX-4 (Upper Handle) | 15-16mm | Steel/Aluminum Alloy | Hot-Dip Galvanized/Natural Aluminum |
Understanding the basic mechanics makes every later decision easier, from sizing to purchasing.
In this case, understanding the basics makes it simple to choose things like what size to buy in the future.
An overhead termination is good in this case because it does four things well. It keeps the tension on the conductor all the time, keeps the strands from getting squished, can handle years of sun, rain, and wind, and is simple to check. It can be very bad in the field if a fitting only meets one of these goals. It's possible for the clamp ranges to not match up, and the bolts can be pushed too far, which can cause the strand to warp. This can be fixed by a Wedge-Type Clamp, which tightens itself. However, it must be the right size and have a load path that has been checked. If you want to buy an overhead line fitting, you can ask any supplier about the test data that supports it. These data are set by IEC 61284 and can be found here.
An eye or bail is used to connect the wedge or gripping insert to the body. There are three main parts to a clamp: the body, the wedge or gripping insert, and the point of attachment. The tube is put in place, and the wire is put inside the body. When the conductor is under tension, the wedge moves deeper into the tapered seat. As the load increases, so does the pressure on the grip. The Wedge-Type Clamp's binding power changes based on the hardware's state and the torque applied. Because they work together, putting wedges and bodies of different types together can change the grip. Our product data also lists a fast-release mechanism that lets you quickly attach and remove it while installing it or making changes later.
Some people think that the carrier and the current can both be carried by the same piece. These are not the same jobs. A Wedge-Type Clamp mechanically holds something in place at a dead-end or anchor point. This is not the same as an electrical joint, a grounding link, or a switch pair. Write down if your plan needs electrical continuity through the termination. Before you place your order, make sure that the maker agrees that it is okay to use. People in the US can use the National Electrical Safety Code (ANSI C2) to follow safe ways to set up and run power and phone lines. Most of the time, local utility standards give you more details. The mechanical and electrical parts of the drawing should be kept separate so that engineers, site supervisors, and purchasing teams can all look at the same file more easily.
Once the mechanics are clear, the next question is where the clamp belongs and where another product does the job better.
Wedge-Type Clamps are used for jobs like grounding, guy-wire, messenger cable, dead-end, and service-drop. It depends on how the conductor was made, how much tension is expected, what kind of weather it will be in, and whether the person who made it agrees with that use. We made our Wedge-Type Clamp to hold and connect wires in power lines that are above ground. The product information also talks about how to clamp structural parts on construction sites, hold them temporarily while they are being put together, and use workstations on assembly lines. It is best to stick to the design and grades that are shown on the drawing when it comes to overhead termination. When the clamp fits a standard setup, the steps are used to install it more than once. This is best for utility workers and builders.
A clamp is big, but that doesn't mean it can do everything. We need to pay more attention to high-tension infrastructure, places where there is a lot of wind or ice, cyclic vibration, strange conductor coatings, and any other place where electricity needs to keep flowing. In this case, an engineer should compare the test results from the manufacturer to the safety factor, the estimated working load, and the ultimate strength. A general wire-rope fitting and an aerial conductor clamp that was made for that purpose are not the same, even though they look the same in size. As per 29 CFR 1910.269 from OSHA, jobs that send and receive electricity are covered. Its rules about turning off power and keeping people safe from falling affect how crews use this gear. Before you send them, please, so that our engineering team has time to go over them with you.
Not all clamps are the same. The Wedge-Type Clamp is small, simple to set up, and it locks itself in place. You can change the screw clamp, but only if you use the right torque and keep the hardware in good shape. To make sure they fit right, wire rope clips have their own rules for where to put them and how to check them. When you use parallel groove clamps to connect or tap conductors, they don't stop the flow of electricity. You could make a mistake if you choose one based on how it looks, how big it is, or how much it costs per unit. Instead, I suggest you compare them based on how they work: as a mechanical termination, an adjustable holding, a rope end, or an electrical connection. People who buy from distributors can also find the right part faster, which is good for them.
A well-chosen clamp still needs proper handling in the field. These three steps cover the full cycle.
In the field, there are right and wrong ways to use a good clamp. There are three steps in this cycle. The first thing you need to do is find out what kind of conductor it is, how it is built, and what it is made of. You also need to know the actual outside diameter of the cable, not just the nominal one. The manufacturer says that the Wedge-Type Clamp's diameter must be within a certain range. It must also have the right working load, ultimate strength, and safety factor. Next, make sure that the finish matches the room. Steel that has been hot-dip galvanized can stand up to being outside for a long time. Iron and steel hardware that is hot-dip galvanized is covered by ASTM A153. First, let us know about the spot. If there is a lot of chemical or ocean exposure, that will help us choose a finish. Not only should you ask for papers and models, but you should also see proof that the wedge and body will be shipped together.
Please check the model against the conductor range and look at the manufacturer's drawing first. Before you use it, check every part. Check to see if the conductor is clean and not broken. When you put the wedge in the body, make sure it's in the right place and that the connection point lines up with the load path. Check for sliding, damage to the strands, uneven sitting, deformation, and breaking that wasn't supposed to happen after the load has been put on. Crews must follow local rules and use fall protection, electrical separation, lockout/tagout, and tools that are insulated. IEEE Std 524 tells you where to put wires for transmission lines that go above your home. People who are trained should be the only ones to install or turn on overhead termination gear.
With regular review, problems are found early on. Watch out for the wire moving, wedge shift, cracks, deformation, rust, coating loss, and damage to the fittings next to it. It's possible to change the frequency based on the load, the vibrations, and the weather. Also, look for places where different metals touch each other. This can make galvanic corrosion happen faster. Since our Wedge-Type Clamp is simple, it's easy to check for damage and keep it in good shape. You should get a new clamp if the old one is permanently bent, severely corroded, cracked, or slips. Also, find out if replacement parts need to come in groups that fit together. The repair staff keeps check records by batch to help them figure out where a problem is coming from.
Technical fit is only half of a purchasing decision. Here is what we offer and what we need from you.
We sell Wedge-Type Clamps that are made of steel or an aluminum alloy. The finish can be silver aluminum or hot-dip galvanized steel. In China, we make things by die casting, forging, and milling. We list ISO9001 and IEC certifications in our product data. The program's goal is to fix and connect wires in power lines that are above ground. We make sure that every clamp works by following the rules for ISO9001 quality management. We make sure the measurements are right, the clamping force is checked, and we choose the right material as part of our quality assurance program. When it comes to quality control systems, ISO 9001:2015 is the gold standard. Still, you should look at the load numbers for each model since the goal is not to rate a single product but to make sure the process is steady.
A detailed question speeds up the quote process. Include the purpose, the type of conductor, the diameter, the working load, the finish, the environment where corrosion can happen, the amount, the packaging needs, the final destination, and any standards that apply. Large and small retailers should also make sure they have enough of the most popular sizes, paperwork, and private-label choices in stock. It's important for contractors and utility teams to check the load path, orientation, and safety inspection again. Procurement experts should not only look at the price per unit, but also at the overall cost, which includes all the things that need to be paid for, like shipping, supplies, extra parts, and the ability to get replacements in the future. They all use the same list of facts, so purchasing managers, engineers, and site leaders can all do their jobs.
There are other things that are useful besides store items. A good company also offers application advice, consistent sizes, wedge-and-body assemblies that match, test records, and a steady supply. For almost 40 years, FLA Industrial & Trading Co., Ltd. has been making more than 1,000 different kinds of hardware tools, Woodworking Clamps, electrical line tools, and pipe fittings made of copper that can be shaped. The Fortune Global 500 trusts us, and we do business in many places, such as the U.S., Germany, and Australia. Standard Products" target="_blank" style="color:blue" >products make up 2,000 tons of our stock. In 7–15 working days, our engineers can make parts in non-standard sizes and shapes with the help of 3D models and updates on the production process.
Overhead wires are held in place by a Wedge-Type Clamp, which changes line stress into holding pressure. So, when the body and wedge fit the load and conductor, the wires don't slip. Keep in mind that electrical continuity is not the same as mechanical preservation. There are several uses for screw clamps, wire rope clips, and parallel groove clamps. The type of wire, its measured outside width, working load, safety factor, and finish are all things that affect the choice. For instance, aluminum alloy and hot-dip galvanized steel aren't always the best choice. A termination will stay stable as long as it is put in place correctly by trained professionals, checked on a regular basis, and care is taken with corrosion and metals that are not the same. Also, buyers should give full technical details and compare total cost, paperwork, and test data instead of just unit price. This is better for buying. Together, these checks cut down on mistakes in the field and make sure the end is still right for what it's meant to do.
The tension makes a Wedge-Type Clamp fit into a body that is tapered. This holds the wires in overhead lines. It says that our model can be used to join and lock together wires in power lines that are above ground.
First, think about the type of conductor and how big it is on the outside. To check if the range and working load are correct, you should use the data from the manufacturer. Think about more than just the width given.
A Wedge-Type Clamp holds something in place mechanically at a dead-end or anchor point. A parallel groove clamp, on the other hand, electrically joins or taps conductors.
You can get steel that has been hot-dip galvanized or metal that is not galvanized. Pick one based on how big it is, how likely it is to rust, and how well it fits with other metals. If the rusting is bad, describe the site.
Send the type of conductor, its outside diameter, its working load, its finish, its surroundings, its number, its location, and any sketches or OEM needs. It takes us 24 to 48 hours to answer.
Need a business that has been making Wedge-Type Clamps for almost 40 years? Clamps made of steel and aluminum alloy are sold by FLA Industrial & Trading Co., Ltd. Of the 2,000 tons of clamps they have in stock, it will take them 7–15 business days to make one that fits your exact needs. Send your number, the type of wire, its diameter, and the amount it needs to carry to sales@flaindustrial.com. You will get prices and more information in 24 to 48 hours. Go to flaindustry.com to find out more.
1. IEC 61284: Overhead Lines – Requirements and Tests for Fittings, 1997
2. IEEE C2: National Electrical Safety Code, 2023
3. OSHA 29 CFR 1910.269: Electric Power Generation, Transmission, and Distribution, 2014
4. ASTM A153/A153M: Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware, 2016
5. IEEE Std 524: Guide to the Installation of Overhead Transmission Line Conductors, 2016
6. ISO 9001: Quality Management Systems – Requirements, 2015
YOU MAY LIKE