The Mechanical Tee Grooved Outlet enables you to connect a branch line to an existing fire protection pipeline without cutting or welding the main line apart. The installer drills a round hole in the pipe, places the housing and gasket over the hole and tightens the bolts. This approach is valuable for retrofits, extensions and phased projects when there are limited hours available for shutdown, the site is difficult to reach, or hot work is not preferred. It can only be used with compatible grooved systems and the model must meet the requirements for pipe, pressure and approval. I will talk about the design, dimensions, installation, options and where to get them so your team will be able to make a sound decision.
| Main Pipe Size | Outlet Size | Main Pipe OD (mm) | Outlet OD (mm) |
|---|---|---|---|
| DN50 | DN25 | 60 | 33 |
| DN65 | DN25/DN32/DN40/DN50 | 76 | 33/42/48/60 |
| DN80 | DN25/DN32/DN40/DN50 | 89 | 33/42/48/60 |
| DN100 | DN25/DN32/DN40/DN50/DN65/DN80 | 114 | 33/42/48/60/76/89 |
| DN125 | DN25/DN32/DN40/DN50/DN65/DN80 | 140 | 33/42/48/60/76/89 |
| DN150 | DN25/DN32/DN40/DN50/DN65/DN80 | 165 | 33/42/48/60/76/89 |
| DN200 | DN25/DN32/DN40/DN50/DN65/DN80 | 219 | 33/42/48/60/76/89 |
The Mechanical Tee Grooved Outlet is a bolted branch connection which covers a drilled hole in an existing pipe. Most designs consist of a lower housing, an upper housing for the outlet, a sealing gasket, bolts, nuts and a grooved branch end. A grooved coupling, fitting or sprinkler part can be used on the branch end. It has a minimum tensile strength of 65,000 psi. It is normally used for casting housings. ASTM A536 Grade 65-45-12 is a grade of ductile iron. The clamps fit around the pipe so the crew doesn't have to cut the main into sections. That’s important in occupied buildings, where a long pipe replacement would be annoying to the tenants and business.
The installer cuts a round hole in the pipe wall and then places the gasket around this hole. The housing covers the gasket and seals. The bolts join the two halves together. This causes the gasket to be pulled tighter against the pipe due to line pressure so it is very important that the gasket is properly seated. The hole fits a collar on the casting to help hold it in place. When the system is under pressure, it prevents the outlet from sliding along the pipe or from rotating. The branch does not only depend on the thin wall of the pipe, the housing also takes the load around the cut.
For welded branches, you need a hot work permit, a fire watch, coating repair, and an inspection. The rules for preventing fires at work are set by NFPA 51B (2019). Most of those steps are skipped with a bolted outlet, which cuts down on time spent in operating facilities. Threaded outlets are good for small connections, but they need to be machined and have their threads sealed, and as the branch size increases, they become less useful. I still tell people to think of the outlet as just one choice, not the only answer. Before asking for it, engineers have to make sure that the pipes will work together, that the branches are the right size, that the pressure is safe, that it meets local codes, and that the fire protection is approved.
It's easy to install because you don't need a hot work permit or any special welding tools. Their job is to drill the hole, place the gasket in place, and use hand tools and a torque wrench to tighten the bolts. That feature speeds up projects and lowers the cost of labor, especially for contractors who plan their work around short shutdown times. It also keeps smoke and sparks from welding out of buildings that people are using, which means fewer alarms go off and fewer places need to be protected. Also, distributors have found that customers who don't have certified welders like this fitting. Don't forget that the pipe still needs to be drained and depressed before you drill. If you skip the weld, you still have to do that safety step.
Our outlets have a protective coating with several layers that keeps them from rusting and makes them last longer. The coating works well indoors and outdoors, even on piping that is left out in the yard or on top of a building, where water can damage bare iron. Epoxy powder coating and hot-dip galvanizing under ASTM A153 are common finishes for this type of product. Buyers should make sure that the model they order has the right finish and thickness. Rust often starts on the edges and pads of bolts and housing, but a sound coating will keep them safe. Even so, I suggest checking exposed outlets often for chips, scrapes, and rust blooms and fixing any damage right away.
The design of a Mechanical Tee Grooved Outlet makes it possible to take it apart and put it back together without damaging the fitting or the pipe. The bolts can be loosened, the gasket can be checked, worn parts can be replaced, and then the housing can be closed again. This makes system changes and repairs easier, which is important when a building owner adds a sprinkler zone years after the system was first set up. Water-based fire protection systems must be inspected, tested, and maintained according to NFPA 25 (2023). Joints that are easy to access make routine checks easier. Remember that reassembly still requires a good gasket, even if the bolts are tightened, and a written pressure test if the authority in charge requires one.
Specification does not begin with nominal labels but with measured facts. Write down the outer diameter of the main pipe, the thickness of the wall, the shape of the grooves, the size of the branches and the space around the pipe. Then you need to know the minimum distance between the fitting or outlet and any other fittings or outlets that have to be nearby. A mechanical tee has a slightly higher friction loss than a welded reducing tee. Branch sizing should be based on hydraulic calculations, sprinkler demand and zoning. Check to be sure the "C" dimension and bolt-pad gap are correct before attaching the coupling. Otherwise the branch will not fit. Always read the data that came with the model from the manufacturer.
Housing is made of ductile iron to ASTM A536 Grade 65-45-12 for high tensile strength and impact resistance. This type of product has a working pressure that can go from 300 psi to 500 psi, but it is dependent on the outlet size and the pipe that fits with it. For further information, please refer to the datasheet of your model. The grade of the gasket is also important. Grade T nitrile is good for oils and Grade E EPDM is good for water from -30F to 230F. NFPA 13 (2022) requires that the hydrostatic test be conducted at a pressure of 200 psi for two hours or at 50 psi above the maximum static pressure if the static pressure is greater than 150 psi. Pick a rating a little higher than your test pressure.
A reliable supplier gives you datasheets, dimensional drawings, installation instructions, pressure tables, data on gaskets, and proof of certification. Check to see if any UL or FM approvals cover the exact model, size, and gasket. Then, find out what kinds of checks are done on production batches. Some useful checks are hydrostatic testing at 1.5 times the rated working pressure, checking the dimensions, testing the hardness and specific gravity of the gasket, looking for cracks in the castings with magnetic particles and your eyes, and measuring the thickness of the coating. Before fittings get to your job site or warehouse, these checks find holes, sand, and the wrong elastomers.
Stick to the approved drawings, the manufacturer's directions, and the safety rules for the job site. First, cut off and drain the line. Then, make sure it doesn't have any pressure in it. Do not drill into a pipe that is under pressure. Mark and measure the centerline of the outlet, make sure there is enough space and access, and then use the right hole saw to cut a round hole. Remove the coupon, the burrs, and any other junk. Check the gasket, only grease it if the manufacturer says to, and place it in the middle without twisting it. In order to set up the housing, line up the branch direction, and tighten all of the bolts evenly. Most of the time, torque ranges from 30 to 200 ft-lbs, so use a torque wrench and the table that was made public. Hold up the branch pipes on their own.
A short list of problems can cause most leaks: holes that are too big or off-center, burrs, paint buildup, debris, damaged or pinched gaskets, uneven tightening, and unstable branch pipes. Before cutting, measure the pipe and make sure the hole size and tolerance are correct for the Mechanical Tee Grooved Outlet. Only use the right gasket and lubricant, and clean the sealing area. It's important to pay attention to the wrench setting because too much torque can damage the gasket, while too little torque can leave a leak path. Tighten the bolts in small, even steps until the housing closes flat. Perform and document a pressure test before putting the system back into service.
Test system per project requirements and NFPA 13 (2022) after the branch is connected. Write down the date , the pressur and the name of inspector . If possible, leave outlets open so that maintenance crews can see them. NFPA 25 (2023) states that the branch should be inspected regularly for corrosion, coating damage, loose fasteners, leaks, gasket aging and outside loads. It’s usually a lot cheaper to fix a small leak early on, than it is to fix water damage in an already finished building. Keep datasheets, installation records and batch numbers all together so MRO teams can find any fitting when they need it.
Where the approved design permits, contractors use a Mechanical Tee Grooved Outlet for drains, retrofit connections, sprinkler branch extensions, and test arrangements. They are often found in warehouses, commercial buildings, industrial plants and construction sites that are being built in phases. Some designs can be used for HVAC lines for chilled water and industrial lines for such items as compressed air. In these cases they absorb the pump vibration and thermal movement better than do rigid threaded joints. Fire safety approval does not mean safe for other fluids or temperature so check each service separately. You will need to match not only nominal pipe size, but also outside diameter, wall thickness, groove profile, pipe material and coupling standard.
The best way to do something depends on whether it's a new build, a retrofit, or an engineered assembly. When installers can open or replace a pipe section, a grooved reducing tee works well. On the other hand, a mechanical outlet saves time on a main that has to stay in place. Welded outlets work well with engineered parts, but they need skilled welders, hot work controls, inspection, and coating repair. Threaded outlets can work for small connections, but they need to be machined, aligned, and have their threads sealed. When deciding between rigid and flexible grooved configurations, you should also think about vibration, movement, thermal expansion, and earthquakes.
Only when the certification, size, material, coating, gasket grade, pressure rating and coating are the same can quotes be compared. Estimate the total landing cost, inclusive of freight, customs, inspection, packing and storage. For large orders, create a size schedule, agree a change process and request samples to confirm the fit is correct before releasing to production. FLA Industrial & Trading Co., Ltd. has been manufacturing hardware tools, Woodworking Clamps, electrical line tools and malleable iron pipe fittings for nearly 40 years and has more than 1,000 product specifications. We partner with some Fortune Global 500 companies and we operate in the US, Germany and Australia. One manufacturer produces a wide range of Products" target="_blank" style="color:blue" >products that can be purchased by distributors and contractors.
The Mechanical Tee Grooved Outlet allows crews to add branch lines to an existing compatible fire protection main without welding or replacing pipe sections. It will work through a drilled hole, a gasket seated under a housing and even with the bolt tightened. It has many useful benefits like no need for hot work, a many layered protective coating and joints that can be opened again to fix or change things. For good results make sure the pipes are the right size, the gasket and pressure rating are correct, the installation is done with care and an NFPA 13 pressure test is done and recorded. In some cases welded, threaded or reducing tee connections still do better. The approvals and compatibility for each model has to be checked. To make fair comparisons of suppliers, the specifications and paperwork must be the same.
No. Separate the pipe, drain it, and make sure there is no pressure in it before cutting the hole, even though welding is not needed.
The collar fits through the hole that was cut. It keeps the outlet from moving along the pipe or turning when pressure is put on it.
For most sizes, torque ranges from 30 to 200 ft-lbs. If you over-tighten the gasket, it can leak, and if you under-tighten it, it can distort. Use a torque wrench and the manufacturer's table.
With a wider radius of curvature and transition hardware, these are the only designs made for plastic pipe. Outlets that are made for iron pipes can crush plastic pipes.
It can only happen if the engineering, code, listing, and project requirements allow it.
Want to find a supplier of Mechanical Tee Grooved Outlet for your next retrofit? Email FLA Industrial & Trading Co., Ltd. at sales@flaindustrial.com with the pipe's outside diameter, wall thickness, branch size, pressure, gasket needs, quantity, and where it needs to go. Our team will help you find the right model and put together a formal quote with drawings and instructions on how to install it. We've been helping distributors, contractors, and MRO teams all over the U.S. for almost 40 years. For more information about the product, go to flaindustry.com.
1. NFPA 13: Standard for the Installation of Sprinkler Systems, 2022
2. NFPA 25: Standard for the Inspection, Testing, and Maintenance of Water-Based Fire Protection Systems, 2023
3. NFPA 51B: Standard for Fire Prevention During Welding, Cutting, and Other Hot Work, 2019
4. ASTM A536: Standard Specification for Ductile Iron Castings, 2019
5. ASTM A153/A153M: Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware, 2016
6. SFPE Handbook of Fire Protection Engineering, 5th Edition, 2016
YOU MAY LIKE