Permanent Screw Jacks hold industrial machinery at a set height for years, not hours. A screw jack turns rotary input into controlled linear motion, so a machine frame, platform, or conveyor can rise, lower, and stay level under load. Unlike shims or wedges, these jacks stay mounted and allow fine adjustment when floors settle or equipment changes. Good results depend on correct load sizing, stroke, speed, duty cycle, and environment. At FLA Industrial & Trading Co., Ltd., we supply screw jacks from 500 kg to 100 tons, and this guide shows how to choose, install, and maintain them.
| Model (t) | Top Cover (mm) | Bottom Cover (mm) | Minimum Height (mm) | Lifting Height (mm) | Weight (kg) |
|---|---|---|---|---|---|
| 3.2 | 49 | 93 | 220 | 110 | 17.4 |
| 5 | 49 | 93 | 250 | 130 | 21.5 |
| 8 | 49 | 104 | 260 | 140 | 22.3 |
| 10 | 59 | 104 | 280 | 150 | 27.2 |
| 16 | 64 | 118 | 320 | 180 | 21.1 |
| 20 | 64 | 128 | 325 | 180 | 23.1 |
| 25 | 64 | 128 | 275 | 130 | 20.9 |
| 32 | 69 | 142 | 395 | 200 | 37.2 |
| 50 | 88 | 186 | 452 | 250 | 36.1 |
| 100 | 125 | 238 | 452 | 200 | 71.3 |
| D10 | 59 | 104 | 200 | 75 | 22.4 |
| D20 | 64 | 128 | 225 | 90 | 19.3 |
| D32 | 69 | 142 | 320 | 150 | 33.4 |
| D50 | 88 | 186 | 330 | 150 | 28.9 |
Most Permanent Screw Jacks have a cover for the gears, a set of worm or bevel gears, a lifting screw, and a nut that moves. Plates hold the unit to a frame, and a dust cover or bellows keeps dust and dirt off of the lifting screw. We temper or quench the lead screw and use bronze or engineering plastic for the nut to make our Permanent Screw Jacks last longer. We choose the right nut material for your duty cycle based on how much it will wear and slide against other things. The body and lifting screw could be made of alloy steel, carbon steel, cast steel, or stainless steel. The metal can be bent to fit the load and the spot where it will be used.
You can turn the input shaft in three different ways: by hand, with a motor, or with a connecting shaft. Worm or bevel gears make the machine move more slowly and give it more force. The torque turns either the lifting screw or the nut, and the load moves along the thread. In one design, it has a lifting screw that moves through the body of the Permanent Screw Jack. Another type of Permanent Screw Jack has a lifting screw that spins and a nut that moves along it. One motor can power more than one Permanent Screw Jack by using shafts and gears. This makes sure that a moving platform or machine frame stays level. The screw lead and gear ratio decide the speed and torque.
There are things that don't let the load push the lifting screw backward when the input stops. As long as the thread lead angle stays below the friction angle, this is likely to happen in a worm gear Permanent Screw Jack. There is a change in the friction. There are a lot of things that can make holding less strong, such as vibration, wear, and the lead on the lifting screw. It is not a safety guarantee, but our Permanent Screw Jacks have a screw mechanism that locks itself shut and holds things in place. You should add a stop, a safety nut, or a second support to a load that is already up before anyone works near it.
Wedges and shims can quickly fix things, but they can move when the floor does, and they need to be worked on again by hand when the floor stops moving. A technician can change the height of a Permanent Screw Jack that stays attached to the frame with a wrench, a handwheel, or a motor. The frame doesn't warp because the load can be spread out among several lifting points by several Permanent Screw Jacks. Still, you need to size the whole machine. You should check more than just the grade on one Permanent Screw Jack. You should also check the shock, toppling moments, duty cycle, temperature, and loads that are moving. Machines with four or more support points often share the load in an unfair way.
As well as being used to align machines and change the height of conveyor belts, Permanent Screw Jacks are also used to work with steel, package goods, build theater platforms, and make workstations more or less adjustable. Our line can also be used to fix vehicles, build buildings, keep bridges in good shape, move loads in a warehouse, and put parts on an assembly line. Housings for heavy rolling equipment need to be able to hold a lot of weight. To make fine adjustments to tools and guides, the positioning must be smooth and correct to the millimeter. Surfaces and bellows that do not rust are needed outside or on wet sites. There should be guards, emergency stops, timing checks, and a written engineering review on a platform that moves people before it is used. For each setting, you should pick a different body, finish, and drive.
Our line goes from 500 kg to 100 tons, so hardware stores can get both light and heavy orders from the same supplier. Permanent Screw Jacks are useful tools for construction workers who need to raise and support structures. There are times when stable, repeatable placement is important, like in furniture and woodworking shops. Desk heights and heavy presses can be changed. Heavy equipment can be fixed with the help of teams from the utility and electrical industries. Moving or lifting big units is easy for crews from plumbing, HVAC, and MRO who use movable bases. We first check the load, stroke, and mounting plan to make sure they are correct. This helps us choose the right model.
Start with the total load and the load per lifting point. Take into account the weight of the equipment, the goods, the fittings, the speed, the shock, and the uneven distribution. Next, check that you have the right room, thread size, attachment size, and stroke. An unsupported screw's length is important because Euler's column theory says that a long, thin lifting screw can break when it is pressed together. It is between 2:1 and 4:1 for safety, and the lift heights are between 100 mm and 2000 mm (about 3.9 to 78.7 inches). It is important to pay more attention to the screw width and guiding when there is a lot of tension and long strokes.
When you change the job cycle and lifting speed, the gear ratio, the input power, and the heat all change too. There is a difference between how a Permanent Screw Jack that moves around a lot and one that moves around a few times during its shift behaves. Because friction makes heat and worm gears don't work as well as bevel gears, it is important to check the constant job. What is around us is also important. We can work in temperatures as low as -20°C and as high as +80°C (-4°F to 176°F). Dust covers, lubrication surfaces, and finishes that can be sprayed on or won't rust can all be useful in dirty, wet, or outdoor areas. If your site falls outside that range, tell us before you place your order.
These are the most important things about our Permanent Screw Jacks.
If you are clear about what you want, the supplier can find you the right Permanent Screw Jack quickly. Send the total weight, the number of lifting points, the stroke, the speed, the duty cycle, the mounting dimensions, the preferred gear, the environment, the drive arrangement, the safety features, the quantity, the destination, and the delivery date. You should not just compare prices, though. You should also look at tech help, testing, customization, documentation, experience with exporting, spare parts, and service after the sale. About 40 years ago, FLA Industrial & Trading Co., Ltd. began making hardware tools, Woodworking Clamps, electrical line tools, and malleable iron pipe fittings. There are more than 1,000 product specifications on our site, and we work with Fortune Global 500 companies. We send prices, weight confirmations, and 3D drawings back within 24 to 48 hours.
Worm gear Permanent Screw Jacks are small and do not backdrive easily, so they can be used for a lot of different tasks. It loses speed and gets hotter when it spins a lot in exchange. But bevel gear Permanent Screw Jacks are more likely to backdrive and need a brake. They work better and can be synced with more than one Permanent Screw Jack through connecting shafts. Choose based on the job first. Worm gearing is often used to make small changes when there is a heavy load that stays in place. If you need to lift things over and over with several Permanent Screw Jacks, you should take a close look at bevel gearing. Our engineers can look at both plans and see how they match up with your job data.
Permanent Screw Jack systems make it possible to place things in a clean, repeatable, and mechanically safe way. Also, they do not use hydraulic fluid, so there is no chance that it will leak. When you set up by hand, you do not need an outside power source, which is useful when you are not near one. When a design is self-locking, the load stays in place even after the wheel stops turning. A pump or pressure line is not needed. Still, hydraulic tools might be better for very high force or high speed because cylinders move quickly when they are pressed. In order to keep something in place for a long time, you should use a Permanent Screw Jack. Use hydraulics to quickly and temporarily lift something heavy.
A mechanical Permanent Screw Jack moves the unit up and down. It can be hooked up to a handwheel, a separate motor, or a control system. A powered actuator that already has a motor connected is often called an electric Permanent Screw Jack. Multi-jack systems use limit switches or encoders to keep track of position. They also have connecting shafts, gears, and PLC drives. Compare the whole system, not just the name of the item. When leveling only once in a while, a hand-driven Permanent Screw Jack works well. But when changing heights often and lifting at the same time, a motorized system is better. To make a unique configuration, let our engineers know in your RFQ if you need brakes, sensors, or a certain way to place the item.
Put the Permanent Screw Jacks on a rigid frame that is straight and level. Frames that are twisted must be able to handle loads that go up and down, side forces, and moments of overturning in order for a Permanent Screw Jack to fix them. Make sure that all the screws, couplings, linking shafts, and gears are lined up in systems with more than one Permanent Screw Jack. Also, set each Permanent Screw Jack to the same point of reference before you connect the motor. Start the commissioning process with nothing on it, and then add load little by little. Check the speed, temperature, synchronization, noise, fasteners, lubrication, safety devices, and repeatability of the machine before putting it to work. Make sure you follow your site's lockout and tagout process when you are setting up.
Service times depend on the environment, the load, the speed, the number of hours the machine has been used, its duty cycle, the lubricant, and how long it has been used. Check for leaks and bad oil. Next, listen for odd sounds and feel for heat. Make sure the bearings, seals, bellows, covers, bolts, connections, lifting screw, and traveling nut are all in the right place. More backlash, higher power needs, vibration, or position shift can all be signs of wear or loads that are not even. A written record of every check helps you see patterns and plan replacements before they break. Our extra lubrication interface makes it easy to grease. When you buy extra parts, be sure to include the model, size, ratio, stroke, and batch number.
A lot of people make these four mistakes. When people buy something, they only look at the estimated load and do not think about side or buckling loads. They also believe that self-locking is always sufficient and fail to notice when the installation is not straight. The service life can be cut short by shock loads, heavy cycling, high speed, heat, shaking, and uneven load sharing, even if the stated capacity seems to be enough. When something is not straight, it can make more noise, wear, and pressure, and it can also throw off the balance of coordinated Permanent Screw Jacks. You can avoid these problems by figuring out the actual operating profile, going over the needs for secondary support and braking, and making sure that maintenance is easy to get to before you place your order. It is much more useful to look at models, job data, and safety conditions than to compare things from a store.
By transforming rotation input into controlled linear motion, Permanent Screw Jacks keep industrial machines level and supported for long periods of time. The type of gear, the material of the nuts and screws, the load at each lifting point, the stroke, the speed, the duty cycle, and the environment can all change how well something works. Worm gears stay small and do not allow back-driving. Bevel gears are more efficient and work better with other gears. For heavy or fast jobs, hydraulic tools can still be used. Self-locking is good for keeping things in place, but it should not be used instead of a safety check. Proper alignment, controlled launch, and regular inspection all add years to the service life. If you choose the right size based on the estimated load alone, you will quickly see wear. To pick the best Permanent Screw Jack for the job, you need to know the duty, stroke, and full load weights.
A lot of the time, they move, level, support, and lift loads for platforms, conveyors, production lines, and machinery.
Start with the total load and the number of points to raise. Then you have to think about shocks, speeding up, and sharing that is not even. The safety factor we have is between 2:1 and 4:1.
No. It can become less stable due to vibration, wear, greasing, and screw lead. If you have a big load, check the brakes or add extra supports.
Yes. We make parts that are not the standard size or shape, and we also use non-standard ways of mounting things. We show you your idea in 3D before we start making it.
Send the quantity, the drawings, the environment, the lifting points, the stroke, the speed, the duty cycle, the total load, and the destination. We will get back to you with quotes, proof of weight, and 3D models in 24 to 48 hours.
If you email sales@flaindustrial.com with your load, stroke, and drawing information, FLA Industrial & Trading Co., Ltd. will help you set up your machine correctly. Permanent Screw Jacks are what we have been making for almost 40 years. Our Products" target="_blank" style="color:blue" >products are ISO 9001 and CE certified, and we can give you a quote within 24 to 48 hours. We have customers from the U.S., Germany, and Australia. Go to flaindustry.com to find out more about the item. After that, get in touch with us to start your inquiry.
1. Machinery's Handbook, 31st Edition, 2020
2. Shigley's Mechanical Engineering Design, 11th Edition, 2020
3. Machine Elements in Mechanical Design, 6th Edition, 2018
4. Marks' Standard Handbook for Mechanical Engineers, 12th Edition, 2018
5. ISO 9001:2015 Quality Management Systems — Requirements, 2015
6. Directive 2006/42/EC of the European Parliament and of the Council on Machinery, 2006
YOU MAY LIKE