Stainless Steel Rope Clips
Application: Used for fastening, connecting, and end termination of wire ropes; widely applied in marine engineering, construction, shipbuilding, and other fields
Appearance: Natural stainless-steel finish, bright surface, corrosion resistant
Place of Origin: China
Manufacturing Process: Precision casting, forging, machining, polishing
Certification: ISO9001, CE
Stainless Steel Rope Clips: AISI 304 and 316 Wire Rope Clamps for Marine and Construction Use
FLA Industrial & Trading Co., Ltd. is a supplier based in China. AISI 304 and 316 fastening hardware is what the company makes. Stainless Steel Rope Clips sit in that range. They hold wire rope, and they can join two lengths or cap off an end. Every clip carries a U-bolt. Two hex nuts and a saddle complete it. Precision casting shapes the part, then forging and machining follow. Polishing comes last. Rust is a worry in marine work, construction, and shipbuilding. The bright natural stainless finish handles those conditions. Non-standard parts and special shapes can also be made from your drawing or sample. Send your price or unit weight request and we answer within 24–48 hours. The same goes for 3D drawing requests.
What Are Wire Rope Clips?
Wire rope clips are known as clamps or grips too. Their job is to secure the end of a wire rope or form a load-bearing eye. The saddle sits against the live end. Over the dead end passes the U-bolt. Tighten the nuts and the rope ends get pressed together inside the saddle. Friction then holds the assembly.
On site that helps. Swaging equipment may not be there, or the termination may need adjusting later. Stainless grades usually win over galvanized parts in wet or salty conditions, where the coating can wear through.

Specifications
The table below lists the data supplied for these this product.
| Specification | Pitch (P) | Total Height (L) (mm) | Hole Diameter (a) (mm) | Screw Diameter (A) (mm) | Shank Diameter (d) (mm) | Clip Height (h1) (mm) | Hexagon Opposite Side (S) (mm) | Applicable Wrench (mm) |
|---|---|---|---|---|---|---|---|---|
| M2 | 0.4 | 17.1 | 4.5 | 3 | 2.5 | 9 | 5.4 | 5.5 |
| M3 | 0.5 | 20.3 | 5.3 | 4 | 3.4 | 8.6 | 6.9 | 7 |
| M4 | 1.25 | 22.7 | 6.6 | 4 | 3.4 | 9.8 | 6.9 | 7 |
| M5 | 0.8 | 26.7 | 7.1 | 5 | 4.3 | 9.4 | 7.8 | 8 |
| M6 | 1 | 32.3 | 7.1 | 6 | 5.2 | 11 | 9.8 | 10 |
| M8 | 1.25 | 34.5 | 10.1 | 6 | 5.2 | 15 | 9.8 | 10 |
| M10 | 1.5 | 44.8 | 10.1 | 8 | 7.1 | 15 | 12.5 | 12.5 |
| M12 | 1.75 | 51.2 | 14.8 | 10 | 8.5 | 18.1 | 15.8 | 16 |
| M14 | 2 | 56.3 | 14.4 | 10 | 8.6 | 21.3 | 15.8 | 16 |
| M16 | 2 | 64.6 | 18.6 | 12 | 10.5 | 24 | 17.8 | 18 |
| M18 | 2.5 | 73.6 | 20.1 | 12 | 10.7 | 29.5 | 17.8 | 18 |
| M20 | 2.5 | 73.9 | 20.5 | 12 | 10.7 | 29.8 | 17.8 | 18 |
| M22 | 2.5 | 76.5 | 25.1 | 12 | 10.7 | 32.5 | 17.8 | 18 |
| M24 | 3 | 79.9 | 27.1 | 12 | 10.7 | 33 | 17.8 | 18 |
| M26 | 3 | 86.6 | 27.8 | 12 | 10.7 | 35.6 | 17.8 | 18 |
| M30 | 3.5 | 100.3 | 33.3 | 16 | 14.1 | 35.6 | 23.8 | 24 |
| M32 | 3.5 | 100.3 | 33.6 | 16 | 14.5 | 35.6 | 23.8 | 24 |
The specification data we supplied does not show a size range. Dimensions are missing too. Unit weight is absent as well, and so are load ratings. Tell us what you need. Details get confirmed with you before you order.
Choosing Between AISI 304 and 316
AISI 304 is a grade people use a lot for construction work and general fastening. Dry conditions suit it. It also holds up where corrosion stays mild.
AISI 316 carries molybdenum, usually 2–3%. Chloride resistance goes up because of that. Coastal sites and marine work are where it usually gets picked. Chemical plants too. Should specific chemicals be in use at your site, check the grade against your exposure conditions before ordering.

Design and Finish
Four steps make up production. First comes precision casting, then forging. Machining follows those, and polishing is the final stage. The saddle groove and the threads are cut while machining. A bright, natural stainless-steel finish appears once polishing is done.
Stainless steel grows a thin chromium-oxide layer on its surface. That layer is what guards the metal against corrosion. Tighten stainless threads dry, or rush them, and galling can happen. So turn the nuts down steadily, and follow the torque guidance for your clip standard.
Two design types are available. DIN 741 style clips are listed as light duty, and US type drop-forged clips and Stainless Steel Rope Clips are listed as heavy duty.

Where These Clips Are Used
Ordinary hardware gives up early once corrosion sets in. This product is the right fit in those spots. Typical uses include:
- Marine and offshore rigging: Salt spray never lets up. Crevice corrosion keeps eating away at yacht rigging and the mooring lines tied up at the dock. Grade 316 is usually the safer pick in that setting.
- Architectural cable systems: Cable railings and balustrades need hardware that looks clean. Rain and dirty city air will hit it too. Vertical garden trellises run into the same trouble.
- Wastewater treatment and chemical processing: Galvanized parts corrode fast near hydrogen sulfide or chlorine. Safety cables and equipment lines in that area take the hit.
- Shipbuilding and general construction: Rope fastening, connecting, and end termination are routine tasks on these sites.

Installation Basics
Fit the saddle on the live end, the side that takes the load. Over the dead end goes the U-bolt. Get the order wrong and the live wires can be crushed. You also end up with a weaker termination.
How many clips you need comes down to two things: the rope diameter and the clip standard. Spacing is set by the same pair. So is the tightening torque. Follow what the clip standard says, and what the rope maker says. After the first load cycle, go back and check the nuts.
For lifting or other safety-critical use, have a qualified engineer confirm the clip type and rating before use.
Quality and Certification for Stainless Steel Rope Clips
ISO9001 and CE certifications come with this product. Maybe your project needs material test reports for Stainless Steel Rope Clips. Or dimensional checks. Or load testing. Let us know before you order. We will come back to you with the records we can supply. You get that confirmation before production starts.
Customization and Lead Time
Special-shaped parts and sizes that are not standard are something we make. They go to machinery makers, building material firms, and other sectors. Most custom jobs move through three stages:
- Early stage: Mold development and 3D design verification, so you can review the product form before production.
- Mid stage: Layout optimization and confirmation of material, performance, and dimensional accuracy.
- Late stage: Production progress updates matched to the delivery schedule.
Custom parts can be completed in 7–15 days. For standard sizes, FLA reports 2,000 tons of inventory. Availability by size and the delivery date are confirmed in your quotation.
FAQ
Q: What does "Never Saddle a Dead Horse" mean?
A: The saddle goes on the live end of the rope, and the U-bolt goes over the dead end. Reversing them can crush the live wires.
Q: How do DIN 741 style and US type clips differ?
A: DIN 741 style clips are listed as light duty. US type clips are drop-forged and listed as heavy duty. Choose according to your load and the standard your project requires.
Q: Can the clips be reused?
A: Reuse is fine when the saddle and U-bolt keep their shape and the threads are still good. Check every part first. Any clip with wear or deformation should be swapped out.
Q: Why choose 316 over 304?
A: Molybdenum is part of Grade 316. That is what makes it stand up better to chlorides. For marine work and chemical plants, people tend to pick it.
Q: How many this product does each termination need?
A: The number depends on the rope diameter and the clip standard. Follow the standard and the rope manufacturer's instructions for the quantity, spacing, and torque.
Q: How quickly can you supply custom parts?
A: Custom and special-shaped parts can be completed in 7–15 days. Price, unit weight, and 3D design requests receive a reply within 24–48 hours.
Contact Us
Send your rope diameter, grade, quantity, Stainless Steel Rope Clips, and any drawing or sample to sales@flaindustrial.com. We reply to price, unit weight, and 3D drawing requests within 24–48 hours.
YOU MAY LIKE















